Speedybee F7 Mini 35A Bluetooth Stack

Op voorraad
Voor 15.00 besteld, vandaag verstuurd


Speedybee F7 Mini 35A Stack TX600 is een complete flightstack die uitermate geschikt is voor mini drones en cinewhoops. Programeren kan via telefoon met Bluetooth!




Specificaties fabrikant


SpeedyBee F7 Mini 35A Stack
Tune FC + ESC without a PC for
your 2-4” quads
Wireless full-featured flight controller tuning
Wireless full-featured BLHeli_S ESC tuning
High-performance F7 flight controller CPU
Real 35A BLHeli_S DSHOT600 ESC
Built-in Bluetooth 4.0 BLE chip
Too difficult to access the
USB port on your compact
2-4" quad? Say goodbye!
It's time to say goodbye to this trouble! With this Bluetooth
stack, you don't need to connect your quad to the PC for
FC and even ESC tuning, everything can be done
wirelessly in the SpeedyBee app.
Tune Flight controller
and ESC wirelessly!
Power the quad, connect the SpeedyBee app via
Bluetooth, configure the UART Ports,PID,OSD and
every other settings on this flight controller.Also,
every parameter of the BLHeli_S ESC in this
stack can be set via the app.
SpeedyBee F7 MINI
Change motor directions
With this stack, when you finish your build, connect to the
SpeedyBee app, change the motor directions just in
a few simple steps. Then take off.
SpeedyBee F7 MINI
Flash Blue Jay firmware for
the ESC wirelessly!
You are a big fan of Blue Jay ESC firmware, because it supports
48k/96k PWM frequency and Bidirectional Dshot? No problem,
the ESC of this stack is loaded with latest Blue Jay firmware.
SpeedyBee F7 MINI
SpeedyBee F7 MINI
SpeedyBee F7 MINI
SpeedyBee F7 MINI
SpeedyBee F7 MINI
SpeedyBee F7 MINI



Product Name SpeedyBee F7 Mini Specs
IMU(Gyro) BMI270 for current batches; MPU6000 for old batches before May 2022.
USB Port Type Type-C
Barometer N/A
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART 6)
Flash FC Firmware Wirelessly Not supported. Please update firmware for this FC on the PC
Download/Analyze Blackbox Not supported. Please download and analyze Blackbox data on the PC
DJI Air Unit Soldering Pads Supported
Flash(for BlackBox) 8MB
Current Sensor Supported, Scale=250 Offset=-500
BetaFlight Camera Control Pad Yes(CC pad)
Power Input 3S - 6S Lipo
5V Output 6 groups of 5V output, five +5V pads and 1 BZ+ pad( used for Buzzer). The total current load is 2.5A.
9V Output 2 groups of 9V output, the total current load is 2A.
3.3V Output Supported. Up to 500mA current load.
ESC Signal Pads M1 - M4
ESC Telemetry UART R4(UART4)
I2C Not supported
LED Pad Used for WS2812 LED
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Used to enter DFU mode
RSSI Input Not supported
SmartPort Use any TX pad of UART for the SmartPort feature.
Supported Flight Controller Firmware BetaFlight(Default), EMUFlight, INAV
Firmware Target Name SPEEDYBEEF7MINIV2 for current batches(Gyro: BMI270); SPEEDYBEEF7MINI for old batches(Gyro: MPU6000) before May 2022.
Mounting 20 x 20mm,  3.5mm hole diameter
Dimension 30 x 30 x 7.5mm
Weight 5.7g
Product Name SpeedyBee 35A BLHeli_S Mini 4-in-1 ESC Specs
Firmware BLHeli_S JH40
Continuous Current 35A * 4
Burst Current 45A(5seconds)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT
Current Sensor Support (Scale=250 Offset=-500)
Mounting 20 x 20mm, 3.6mm hole diameter
Dimension 35 * 35 * 5.5mm
Weight 7g
Wij slaan cookies op om onze website te verbeteren. Is dat akkoord? Ja Nee Meer over cookies »